The companies benchmark eco-design attributes of investment casting and DMLS™ Additive Manufacturing (AM)

KRAILLING, Germany & NOVI, Mich. — (BUSINESS WIRE) — February 4, 2014 — EOS, technology and market-leader for design-driven, integrated e-manufacturing solutions in the Additive Manufacturing (AM) sector, has collaborated with Airbus Group Innovations (previously EADS Innovation Works), of Filton, Bristol, to complete an environmental lifecycle comparison of two key production technologies, rapid investment casting and Direct Metal Laser Sintering (DMLS™).

The Airbus Group Innovations-EOS eco-assessment, applied to an Airbus A320 nacelle hinge bracket (a highly standardized part), strove to include detailed aspects of the overall lifecycle: from the supplier of the raw powder metal, to the equipment manufacturer (EOS), and to the end-user (Airbus Group Innovations). Adapted from Airbus’ streamlined lifecycle assessment (SLCA) and ISO 14040 series requirements data, the testing will serve as the basis for continued “Cradle-to-Cradle” study into other aerospace parts, processes and end-of-life strategies.

“We have worked in a bold, new collaboration with Airbus Group Innovations on integrating business and ecological sustainability from sourcing through to product development,” said Nicola Knoch, environmental and sustainability consultant to EOS. “There is now a valuable, holistic baseline established on our technology regarding the measurable costs, benefits and impacts of DMLS. This sets the groundwork for future technology developments in Additive Manufacturing and further studies.”

As a first step, the SLCA was conducted on a generic bracket benchmarking the DMLS process with a conventional casting process used as the baseline. Comparing the lifecycle of a steel bracket (casting process) with the lifecycle of a design-optimized titanium bracket (DMLS):

• The use phase has by far the biggest impact in terms of energy consumption and CO₂ emissions over the whole lifecycle of the bracket.
• CO₂ emissions over the whole lifecycle of the nacelle hinges were reduced by nearly 40 percent via weight saving that resulted from an optimized geometry, which is enabled by the design freedom offered by the DMLS process and the use of titanium.
• Most significantly, using DMLS to build the hinge may reduce the weight per plane by 10 kilograms, a noteworthy saving when looking at industry “buy-to-fly” ratios.

The second phase of the analysis focused on the manufacturing process for the design-optimized bracket using titanium as an ideal, common material—and, this time, benchmarking the manufacturing process of investment casting against that of DMLS via the EOSINT M 280 system:

• The total energy consumption for creating the initial raw powder metal, then producing the bracket in DMLS, was slightly smaller than the equivalent cast process steps (with the higher energy use of DMLS limited to the melt and chill cycle of its manufacturing profile and offset at the same time by a significantly reduced build time). Casting in this comparison was burdened with the furnace operation of burning an SLA (stereolithography) epoxy model, which uses considerable energy and generates greenhouse gases.
• The DMLS process itself used only the material actually needed to make the part—thereby eliminating waste from secondary machining and reducing consumption of titanium by 25 percent over the cast application.

“DMLS has demonstrated a number of benefits, as it can support the optimization of design and enable subsequent manufacture in low-volume production,” said Jon Meyer, Additive Layer Manufacturing Research Team Leader, in his final report. “In general, the joint study revealed that DMLS has the potential to build light, sustainable parts with due regard for the company’s CO₂ footprint.”

For more information on the Airbus Group Innovations-EOS study and its goals, parameters and results go to: http://www.eos.info/press/customer_case_studies/eads or http://tinyurl.com/l2hsgl3.

About EOS

Founded in 1989 and headquartered in Germany, EOS is the technology and market leader for design-driven, integrated e-Manufacturing solutions for Additive Manufacturing (AM), an industrial 3D printing process. EOS offers a modular solution portfolio including systems, software, materials and material development as well as services (maintenance, training, and specific application consulting). As an industrial manufacturing process it allows the fast and flexible production of high-end parts based on 3D CAD data at a repeatable industry level of quality. As a disruptive technology it paves the way for a paradigm shift in product design and manufacturing. It accelerates product development, offers freedom of design, optimizes part structures, and enables lattice structures as well as functional integration. As such, it creates significant competitive advantages for its customers. For more information please visit www.eos.info.

Note to Editors :

As of the 1^st January 2014, Airbus Group Innovations became the new name of EADS Innovation Works. For reasons of timing, the report, compiled prior to this rebranding refers throughout to EADS Innovation Works. More information on the brand change here: http://www.airbus-group.com/airbusgroup/int/en/news/press.20140102_airbusgroup_new_brand.html

Photos/Multimedia Gallery Available: http://www.businesswire.com/multimedia/home/20140204005189/en/

Contact:

Parker Group (editorial US)
Miles Parker, +1 401-272-1510
Email Contact
or
EOS-Electro Optical Systems, GmbH
Claudia Jordan, +011 49 (0) 89 893 36 x2134
Public Relations Specialist
Email Contact
or
EOS of North America, Inc.
Electro Optical Systems
Jessica Nehro, +1 248-306-0143 x8104
Field Marketing Manager
Email Contact