ASSURE Announces Results of Phase II Ground Collision Study

HUNTSVILLE, Ala., Aug. 14, 2019 — (PRNewswire) —  Digital Media Kit:  https://pr.cirlot.com/assure-announce-results-of-phase-ii-ground-collision-study/

 What could happen if a drone hit a person on the ground? What are the risks of serious injury from flying small unmanned aircraft over people, and are we doing everything we can to reduce those risks?

Through its continued research, the Alliance for System Safety of UAS through Research Excellence (ASSURE), has developed a standard methodology by which potential injury may be evaluated.

The ASSURE research team, led by The University of Alabama in Huntsville and including Mississippi State University, The National Institute for Aviation Research (NIAR) at Wichita State University, and The Ohio State University, will release the findings of its 18-month, Air to Ground Collision study of small unmanned aircraft systems (sUAS) at a press conference this afternoon at The University of Alabama in Huntsville.

The team's new research findings and data may help inform the FAA and industry of operational limitations for Small Unmanned Aircraft Systems (sUAS) when operating over people. It will also provide new data from which sUAS design specifications may be developed to further reduce risk to people and property on the ground.

"The research results give the FAA a better picture of potential injuries and their severity, based on established science," said Stephen P. Luxion, Col (Ret.), Executive Director, ASSURE. "Earlier testing of injury data strongly supported our assessment that long-standing fatality data was overly conservative and largely not applicable to injuries resulting from impacts by more elastic sUAS. Additional testing was needed to develop a more accurate, science-based test methodology that may be used  by the FAA, sUAS manufacturers, and operators of sUAS to evaluate the injury risk potential."

"The Ground Collision Severity Evaluation does not seek to advocate for any new rules or regulations, but rather may inform the rulemaking process by increasing the body of scientific knowledge for the FAA, industry and UAS manufacturers," said David Arterburn, Director, Rotorcraft Systems Engineering and Simulation Center at The University of Alabama in Huntsville and principal investigator for the study. "Rather than speculate on the possibility for injury, the new report also allows manufacturers access to sufficient data that could be used to create new industry consensus standards that reduce the potential of human injury risk for flight over people operations."

The scope of earlier studies was limited to testing of a single vehicle, with a limited number of impact tests, and no correlation of the testing results to actual human injury.

The ASSURE research team was sponsored by the FAA to assess injury potential of various sUAS of different material properties and construction. The team conducted fixed-wing and multi-rotor sUAS failure flight testing and aerodynamic modeling, full anthropomorphic test device (ATD) impact testing, simplified head and neck only ATD impact testing, Post Mortem Human Surrogate (PMHS) impact testing, ATD and human-body model impact simulations, and high-fidelity head and neck only impact simulations.

Over 512 impact tests and simulations were conducted using 16 different multi-rotor and fixed-wing sUAS, as well as various objects and payloads (batteries, wood blocks, etc.) with weights ranging from 0.71 to 13.2 lbs. Testing also included evaluation of heavier sUAS using mitigations to reduce potential for injury, such as sUAS under parachutes.

"The injury impacts conducted in the study were controlled impact tests of the worst case, using those variables capable of transferring the most energy to a human," said Arterburn. "Even in these controlled studies, slight variations of the vehicle orientation or location of impact with the human, just prior to impact, reduced the injury potential. These results showed that these worst-case impacts are very difficult to achieve, even under controlled impact test conditions."

"This data and the continued work that the ASSURE program is conducting may help inform future safety decisions for UAS integration in our National Airspace System," continued Luxion.

The complete report is available at  http://www.assureuas.org/projects/deliverables/sUASGroundCollisionReport2017-2019.php.

ABOUT ASSURE

ASSURE's UAS focus is on research, education, and training critical to safe, efficient, and successful integration of UAS into the nation's airspace. ASSURE has conducted initial research in: detect and avoid technology; low-altitude operations safety; control and communications; spectrum management; human factors; maintenance standards and requirements; compatibility with air traffic control. ASSURE membership is made up of 15 core universities, 8 affiliate universities, and over 110 industry partners. ASSURE membership includes representation in 13 states, 9 countries, and over 200 locations, and is core to 3 UAS Test Sites. Learn more at  ASSUREuas.org.

Cision View original content to download multimedia: http://www.prnewswire.com/news-releases/assure-announces-results-of-phase-ii-ground-collision-study-300901901.html

SOURCE ASSURE

Contact:
Company Name: ASSURE
Anna Neel
Email Contact 769-798-6322
Web: http://www.ASSUREuas.org

Featured Video
Editorial
Jobs
Equipment Engineer, Raxium for Google at Fremont, California
Mechanical Engineer 2 for Lam Research at Fremont, California
Senior Principal Mechanical Engineer for General Dynamics Mission Systems at Canonsburg, Pennsylvania
Manufacturing Test Engineer for Google at Prague, Czechia, Czech Republic
Mechanical Manufacturing Engineering Manager for Google at Sunnyvale, California
Mechanical Test Engineer, Platforms Infrastructure for Google at Mountain View, California
Upcoming Events
Celebrate Manufacturing Excellence at Anaheim Convention Center Anaheim CA - Feb 4 - 6, 2025
3DEXPERIENCE World 2025 at George R. Brown Convention Center Houston TX - Feb 23 - 26, 2025
TIMTOS 2025 at Nangang Exhibition Center Hall 1 & 2 (TaiNEX 1 & 2) TWTC Hall Taipei Taiwan - Mar 3 - 8, 2025
Additive Manufacturing Forum 2025 at Estrel Convention Cente Berlin Germany - Mar 17 - 18, 2025



© 2024 Internet Business Systems, Inc.
670 Aberdeen Way, Milpitas, CA 95035
+1 (408) 882-6554 — Contact Us, or visit our other sites:
AECCafe - Architectural Design and Engineering EDACafe - Electronic Design Automation GISCafe - Geographical Information Services TechJobsCafe - Technical Jobs and Resumes ShareCG - Share Computer Graphic (CG) Animation, 3D Art and 3D Models
  Privacy PolicyAdvertise